Cooper-instruments-systems M5-1000 High Capacity Digital Force Gage Manuel d'utilisateur

Users Guide Series 5 Digital Force Gages www.cooperinstruments.com PH: 540-349-4746  FAX: 540-347-4755

CF 183 7 32-1113 REV 2 1010 Trigger Force The minimum force required to start the averaging sequence. Toggle between compression and tens

CF 183 8 32-1113 REV 2 1010 Note: As long as external trigger has been enabled, it is still active even if the gauge is in Real Time mode.

CF 183 9 32-1113 REV 2 1010 If two set points have been enabled, they are displayed in the upper left corner of the display. If only one

CF 183 10 32-1113 REV 2 1010 Press ENTER to delete the value. To exit Delete mode, press DELETE again. Any number of readings may be ind

CF 183 11 32-1113 REV 2 1010 13 Click “Install”. 3. The next screen appears as follows: Click “Continue Anyway”. 4. After installati

CF 183 12 32-1113 REV 2 1010 14 Select “No, not this time”, then click “Next”. 6. The next screen appears as follows: Select “Install

CF 183 13 32-1113 REV 2 1010 Click “Finish”. The USB device is now installed and ready to use. The COM port number assigned by Windows m

CF 183 14 32-1113 REV 2 1010 Select Enabled to activate automatic output. The number of outputs per second can be set to 1, 2, 5, 10, 25,

CF 183 15 32-1113 REV 2 1010 9.7 I/O Connector Pin Diagram (female) Pin No. Description Input / Output 1 Signal Ground --- 2 Tensio

CF 183 16 32-1113 REV 2 1010 PC Peak Compression mode for primary reading CLR Clear peaks Z Zero display and perform the CLR functio

This page intentionally blank

CF 183 17 32-1113 REV 2 1010 RS Read serial number Other Commands AOFFn Auto-shutoff. n=0-30 minutes. 0=auto shutoff disabled SAVE Sa

CF 183 18 32-1113 REV 2 1010 Selecting “CANCEL” will revert back to the Calibration setup. Selecting “EXIT W/O SAVING” will return to the

CF 183 19 32-1113 REV 2 1010 Optionally exercise the load cell shaft several times (at full scale, if possible), then press ENTER. 8. The

CF 183 20 32-1113 REV 2 1010 Reverse the orientation of the load cell shaft by rotating the gauge 180 degrees. Press DIRECTION to invert t

CF 183 21 32-1113 REV 2 1010 11.1 Calibration Password Select Calibration from the sub-menu. The display will appear as follows: To s

CF 183 22 32-1113 REV 2 1010 12 OTHER SETTINGS 12.1 Automatic Shutoff The gauge may be configured to automatically power off following a p

CF 183 23 32-1113 REV 2 1010 12.5 Initial settings This section is used to configure the initial settings upon powering on the gauge. Th

CF 183 24 32-1113 REV 2 1010 Parameter Setting Set points Upper Lower Disabled (defaults to 80% of full scale when enabled) Disabled (de

CF 183 25 32-1113 REV 2 1010 13.4 Dimensions 14 WARRANTY Limited Warranty on Products Any Cooper Instruments product which, under norma

CF 183 ii 32-1113 REV 2 1010 Table of Contents 1 OVERVIEW...

CF 183 1 32-1113 REV 2 1010 Thank you for purchasing a Cooper Series 5 digital force gauge, designed for tension and compression force tes

CF 183 2 32-1113 REV 2 1010 3. The gauge should be serviced by a trained technician only. AC power must be disconnected and the gauge must

CF 183 3 32-1113 REV 2 1010 reassemble. Contact between the two halves is made by the spring pins and contact pads on the printed circuit

CF 183 4 32-1113 REV 2 1010 4 HOME SCREEN AND CONTROLS 4.1 Home Screen No. Name Description 1 Measurement direction - indicates a compr

CF 183 5 32-1113 REV 2 1010 8 Battery / AC adapter indicator Either the AC adapter icon, battery icon, or no icon will be shown, dependi

CF 183 6 32-1113 REV 2 1010 For parameters requiring the input of a numerical value, use the UP and DOWN keys to increment or decrement t